11390a
Ma i n t e n a n ce Co
n s t r u c ti on
M a t e r i a ls
A p li c a ti on
ALL
1 1 3 9 0 a
SIDEFLEXING CHAINS WITH HIGH FRICTION SURFACE
878 TAB VG - 879 TAB VG
RD = 50 mm 45 mm (1.77 in) 42,1 mm (1.66 in) 4,8 mm 16 mm (0.63 in) 61 mm (2.4 in) 15 mm (0.6 in) 60 mm (2.36 in) 7,55 mm (0.3 in) 0 7,14 mm (0 0.28 in) 11,5 mm (0.45 in) 3 mm (0.12 in) 38,1 mm (1.5 in) L R. (0.19 in) (RD = 1.97 in) RD = 50 mm (RD = 1.97 in) R. 15 mm (0.6 in) 45 mm (1.77 in) 42,1 mm (1.66 in) 38,1 mm (1.5 in) 8,3 mm (0.33 in) 7,05 mm (0.28 in) 60 mm (2.36 in) 61,8 mm (2.43 in) L 11,8 mm 4,8 mm (0.19 in) (0.46 in) 3 mm 20,8 mm (0.82 in) (0.12 in)
ITEM DESCRIPTION MATERIAL BREAKING LOAD WIDTH L R MIN. WEIGHT PLATE RUBBER N lbs mm in mm in Kg/m lbs/ft.
NGE878TAB-K325VG
NGE Grey Blue TPR Water blue 70 shore A 4500 1000 82,5 3 190 7.5 1,08 0.73 ITEM DESCRIPTION MATERIAL BREAKING LOAD WIDTH L R MIN. WEIGHT PLATE RUBBER N lbs mm in mm in Kg/m lbs/ft.
NGE879TAB-K325VG
NGE Grey Blue TPR Water blue 70 shore A 4500 1000 82,5 3 500 19.7 1,05 0.7
NGE879TAB-K450VG
114,3 4 1,25 0.84
Characteristics:
Turning disks can be used, as the chain is designed to turn around a very small curve radius.
Pin material:
Austenitic steel
Pin material:
Austenitic steel For Drive Disks, go to
Nolu -S curves
are strongly recommended with these chains!
Other versions 878 TAB: FT Flat top GS Gripper LBP (low pressure) FT Flat top TRAVEL Other versions 879 / 880 TAB: FT Vacuum See also the sprockets and idler wheels: See also the sprockets and idler wheels:
Revision 001
www.SystemPlastSmartGuide.com
1 1 0 1 0 a 5 3 5 1 0 a 5 0 5 1 0 a 3 0 0 1 0 a 5 4 0 1 0 a 5 1 0 1 0 a 5 0 0 0 5 a 5 4 5 1 0 a 5 1 5 1 0 a 5 5 5 1 0 a 5 6 0 1 0 a 5 7 0 1 0 a 7 2 0 1 0 a
1 1 2 6 0 a 1 1 2 7 0 a 1 1 2 6 0 a
11350a
7 3 7 0 0 a
11430a 11230a
5 0 1 1 0 a
11235a 11230a
Chains & sprockets Wear strips Side guide brackets & accessories Levelers Engineering manual Modular belts & sprockets Chain & belt return systems Frame & structure supports Bearing supports Curves & tracks Side guide solutions Miscellaneous products Equipment
NG
evo
conveyor components made from engineered plastic resin
Longer wearlife than acetal Lower friction than acetal Good chemical resistance High abrasion resistance It meets the requirement for materials as stated by EC1935/2004 and FDA CFR21 norms for direct food contact Less dust than with acetal chains More.........
NG
evo
conveyor components made from engineered plastic resin
Longer wearlife than acetal Lower friction than acetal Good chemical resistance High abrasion resistance It meets the requirement for materials as stated by EC1935/2004 and FDA CFR21 norms for direct food contact Less dust than with acetal chains More.........
Previous Page